1977-1987 Land Rover / Range Rover V8 Pro Series Ready to Run Distributor - Black

Upgrade your 1977–1987 Land Rover, Range Rover, or Rover-powered vehicle's 3.5L (3528cc) aluminum V8 with this Pro Series Ready-to-Run distributor, featuring an onboard circuit board ignition module paired with a magnetic pickup trigger — so there's no separate ignition box to wire in. This distributor supports Range Rover Classic, Series III Stage One V8, Land Rover 90/110, and Rover SD1 applications.

This distributor is designed for carbureted 1977–1987 Rover V8 engine combinations only. The housing is machined aluminum with a steel drive gear best matched to cast iron hydraulic or solid flat-tappet camshafts. This distributor requires a 12-volt electrical system with an alternator and a coil rated at 35,000 volts or higher; it is not compatible with generator-based charging systems or vehicles still running an active ballast resistor in the ignition circuit — the resistor should be removed or bypassed as part of installation.

What Is a Ready-to-Run (RTR) Distributor?
An RTR distributor has the ignition control module built directly into the housing, so it fires off a single 12-volt source without needing a separate ignition box wired into the circuit. This unit pairs that onboard module with a circuit board ignition control and magnetic pickup trigger, replacing the factory Rover V8 breaker-point distributor. The coil stays external here, requiring a coil rated at 35,000 volts or higher.

Performance Benefits
The circuit board module and magnetic pickup trigger hold timing steady without the wear and drift of a points-based system, a meaningful upgrade for restoring reliable ignition on these classic Rover V8 applications. Mechanical and vacuum advance are both included, with a vacuum advance adjustment tool in the box so the timing curve can be tuned for carbureted street or off-road driving.

COMPATIBLE WITH
LAND ROVER / ROVER ALUMINUM V8
• 3.5 L / 215 in³ (3,528 cc)

NOTES
• Designed for carbureted 3.5L Rover V8 applications from 1977–1987 only.
• The Rover V8 transitioned to fuel injection from 1988 onward — this distributor is not compatible with EFI applications.
• The Rover V8 is an aluminum block engine originally derived from the Buick 215 — it is not related to any American V8 and shares no components with Ford, GM, or Chrysler distributors.
• Requires an external coil with a minimum output of 35,000V — no separate ignition box required.
• This distributor is designed for a 12 volt electrical system with an alternator and a performance ignition coil of 35,000 V or more. 
• It is not compatible with a generator and cannot be used with a ballast resistor.
• Distributor gear is most compatible with cast iron hydraulic or solid flat tappet camshafts; consult camshaft manufacturer for recommended gear material before installation.

COMMON VEHICLE APPLICATIONS
Land Rover Range Rover Classic (3.5L, 1977–1987)
Land Rover Series III Stage One V8 (3.5L, 1979–1985)
Land Rover 90 (3.5L, 1983–1987)
Land Rover 110 (3.5L, 1983–1987)
Rover SD1 3500 / Vitesse (3.5L, 1977–1986)
Triumph TR8 (3.5L, 1980–1981)
Morgan Plus 8 (3.5L, 1977–1983)

SPECIFICATIONS

Distributor Type: Pro Series Ready to Run
Trigger Style: Circuit Board Module with Magnetic Pick-up
Advance Type: Mechanical and Vacuum
Cap Color: Black
Cap Style: Male
Mechanical Tach Drive: No
Slip Collar: No
Coil Included: No
Coil Type: External
Required Coil Output: 35,000+ Volts
Gear Material: Steel
Housing Material: Machined Aluminum
Ignition Box Required: No
Cylinders: 8
Marine Use: No
Included: 3 Bushings and 4 Springs for Mechanical Advance
Color-Matched Spark Plug Wire Retainer with Screws
Vacuum Advance Block-off Plate (Black)
Power Extension Cable
Tachometer Output Extension Cable